Cybertec 2000 manual

Table Of Contents. Table of Contents. Previous Page. Next Page. Related Manuals for Cybertec Series No related manuals. Cybertec Pty Ltd reserves the right to revise this document or withdraw it at any time without prior notice. Page 3: Table Of Contents 6. No connectors or indicators are located on the rear panel.

Refer to Section 5 for installation details 4. Page 4 of In normal operation the indicator will be green, if a fault is detected either at boot-up or during normal operation the indicator will light red. Page 7: Factory Default Reset Switch 4. The switch is accessed through a small hole adjacent to the indicators, refer to Figure 2. Refer to the image on the left of Figure 5 for the location of the SIM card eject buttons.

Page 9: Antenna 5. The supplied antennae are intended for direct mounting to the SMA connectors. Attach the antenna as shown in Figure 6. Ensure that the connecting nut is done up tightly in order to make a good connection. Page 10 of A login box similar to Figure 10 will pop up. If the box fails to display, re-check the cable connections to the unit and the IP address settings of the PC. Page 51 Document: Version: 1. It is mainly intended for the transport of serial data.

Connections are established by dialing into the modem using a PSTN modem or dialing out a call via AT commands on the serial port. The default setting is for the Series to operate on all supported frequency bands. Figure Frequency Band Selection - Custom Once any changes have been made to the frequency bands click the Update button the commit the changes. Once the state has been set, the modem will attempt to establish a connection.

Page 56 Document: Version: 1. The page will update and the selected index will now be highlighted. Page Connection Management Poor signal strength. Check the antenna is properly connected and experiment with different locations for the Series to achieve a higher RF Level. Problem with the SIM card.

Page 60 Document: Version: 1. Page 61 Should the connection maintenance test fail then the Series will attempt to re-establish the connection. If this value is set to No a DNS server should be entered manually. The Model has 1 serial port so only while serial port will be listed while Model has 3 serial ports so 3 will be listed.

Page 65 Document: Version: 1. Page Sms An SMS will be returned providing current status information. Reboot Initiate a reboot. Wireless Packet mode Switch to packet mode. Click the OK button to remove the entry. Page 74 Document: Version: 1. Click the Update button once changes have been completed to save the changes. Page 77 Page 78 of Page Network Figure is an example of the LAN settings page. To access the diagnostic tools, select Network Diagnostics.

Page 90 Document: Version: 1. The main page will again be shown with the new route added, as seen in Figure A warning box will A static route can be deleted by clicking the be displayed.

Page Dynamic Routing RIP is a dynamic routing protocol used in local and wide area networks and is supported in many routers. Page 94 Document: Version: 1. This may make the internal web server temporarily unavailable until the change in address has propagated.

Page 97 Document: Version: 1. The main Policy Route page will again be shown with the new route listed, as shown in Figure Page 98 Document: Version: 1.

The main page will again be displayed as shown in Figure , with the changes for route 2 added to the table. Page Document: Version: 1. Only packets matching this source address will have the route applied to them. This indicates these are the matching criteria that will be applied to packets. All criteria that are unchecked will be ignored. Figure QoS route table with route two removed Page Firewall When selected the page shown in Figure will be displayed.

It controls which services can be accessed from the wireless port and VPN tunnels. Page Custom Filters Document: Version: 1. Select the appropriate protocol from the list. The main page will again be shown with the new port forward added, as seen in Figure Note that this can only be applied to a Source NAT.

In the example shown in Figure , a destination NAT is created for packets destined for the wireless port. The main page will again be displayed as shown in Figure , with the changes for custom NAT 2 added to the table.

A warning box will now be displayed as shown if Figure The options are The local ID will present a hostname as its ID. The phase 2 options are: Authentication method Select the extended authentication method, the options are: None No extended authentication. Generally only used by responder. Restart Attempts to restart the tunnel. Generally set for initiator.

Restart by peer Restart every tunnel associated with the peer. It will operate in Tunnel mode and will act as the initiator. Margin 10 Minutes. Dead Peer Detection Enable Check to enable. For most applications the default options do not need to be changed. Page This section describes an example of connecting to a VPN server.

Figure illustrates the network which will be estab- lished. Figure illustrates the network which will be established. Page Multiple Vpn Tunnels Page When the icon is clicked a warning box will be displayed. Page Serial Server Server is selected by clicking Serial Server on the main menu, a page similar to that shown Figure will be displayed for the Series , Model of Figure for the Model The difference between models being the number of ports listed. The table provides a summary of the port settings.

The columns have the following meanings: Port The port number this corresponds the physical port number. Once established the connection acts in a similar way to other packet interfaces.

Example uses of this mode include connecting to a remote PC running serial port redirector software with virtual COM ports or connecting two modems back-to-back to create a serial bridge. The address entered should be in IPv4 decimal dotted notation. If set, the new connection will become the active connection and the existing connection will be closed.

The value entered should be a valid TCP port number.